Portable Sensor Display Strain Bridge Input (PSDS)
- ​High resolution ADC providing sensitivity of between 7.5 mV/V to 480 mV/V. (3.3 VDC Excitation)
- Strain bridge connector for six wire connection plus TEDS support
- Two point calibration via the keypad or comprehensive calibration options via the toolkit.
- Simple keypad configuration or fully customised via toolkit software
- 128 x 64 dot matrix display with backlight
- USB port providing configuration, calibration, save & restore, live logging
- Measurement rate up to 2,400 SPS
- Ergonomic design with improved grip and shock protection
The PSDS allows simple display of strain bridge based measurements such as load cells and pressure gauges with sensitivity up to +/-480 mV/V.
Up to six calibration ranges are available allowing for different loading modes (tension and compression) or different sensors. Each calibration range will remember settings that contribute to the user experience such as selected units and tare values.
TEDS devices using templates 33, 40 and 41 can be connected and will update the viewed calibration.
Up to six display modes available. These determine what is visible on the LCD display and what actions are available from the set of three soft keys.
Full configuration is available with a free PC based toolkit, requires right angle cable. Some simple configuration such as two point calibration is available from within the handheld using the menu system.
This module can be either used as a handheld device or, using the optional mounting accessories, or attached to equipment, dashboards, walls or desks. Binder connectors need to be ordered separately.
The PSDS is powered by two internal non-rechargeable AA alkaline batteries. Binder connector required.
Strain Gauge Measurement
| Parameter | Min | Typical | Max | Units | Note |
|---|---|---|---|---|---|
| Measurement Method | 6 Wire | Can accept 4 wire input | |||
| Excitation Voltage | 3.2 | 3.3 | 3.4 | VDC | |
| Drive Capability | 85 | - | 10,000 | Ohm | |
| Sensitivity FSR Ranges ¹ |
±7.5 |
- | ±480 | mV/V | |
| Linearity ² | ±2 | ppm/FSR | In high quality operating mode | ||
| Offset Temperature Stability | 12 | nV/°C | |||
| Internal Resolution | 24 | bit | |||
| Resolution at 1 SPS | 1,100,000 (20) | Counts (bit) | Noise free at ±7.5mV/V range | ||
|
Resolution at 10 SPS |
550,000 (19) | Counts (bit) | |||
| Resolution at 2400 SPS |
6,500 (14.3) |
Counts (bit) | |||
| Filters | |||||
1 - Effective sensitivity from ±0.5mV/V with relative resolution
2 - Linearity error can be further reduced by device linearization calibration
Electrical, Mechanical & Environmental
| Parameter | Min | Typical | Max | Units | Note |
|---|---|---|---|---|---|
| Display Resolution | 128 x 64 | pixels | |||
| Buzzer Acoustic Output | 45 | dB | |||
|
Power Supply ³ |
2x AA (LRx) or USB powered |
||||
| Power Consumption | 35 | mA | Measurement operation | ||
| Standby Current | 75 | uA | |||
| Battery Life Low Quality 1Hz | 220 | Hrs | |||
| Battery Life High Quality 1200Hz | 60 | Hrs | |||
| Operating Temperature Range | -10 | 50 | °C | ||
| Storage Temperature Range-20 | -20 | 80 | °C | ||
| Operating Humidity Range | 0 | 95 | %RH | ||
|
Environmental Protection |
IP64 (With connector mated or unmated) | ||||
| External Dimensions | L: 170mm, W: 94mm, H: 42mm | Excluding mated connector | |||
| Weight | 365 | g | Including batteries | ||
3 - Using Energizer L91 3000mAh cells
.png)
Documents
- PSDS Manual : Full instructions for the Portable Sensor Display
- PSDS Quick Start Guide
- PSDS Brochure
Software
- PSD Toolkit : Version 01.5.0 For configuration of next generation PSD handheld modules.
Product order options
| PSDS | Code |
|---|---|
| Portable Sensor Display Strain Bridge Input | PSDS-HSBK-A |
| Accessories | Code |
| Binder Connector 770 6-8mm | 427-741 |
| Binder Connector 770 4-6mm | 427-739 |
| USB Right Angle Cable | ACC-CB-A |
| PSDS Sensor Conversion Cable | ACC-CB-B |
| Magnetic Mount for Handheld | ACC-MT-A |
| Fixed Mount for Handheld | ACC-MT-B |
| PSDS Black Leather Carry Case | ACC-CC-A |
